go-eCharger HOMEfix 11 kW A-Quality

Item number: CH-02-18-1

EAN: 9120087410309

Our smallest wallbox with 11 kW for charging electric vehicles at home or company parking lots with built-in type 2 socket and 2 m connection cable (WITHOUT PLUG). Apart from mobility, the go-eCharger HOMEfix offers the same functionality as the go-eCharger HOME+ (with plug). The Charger is designed for permanent installation at a fixed location.

A major advantage of installation compared to the classic wall charging station - the go-eCharger HOMEfix can be quickly connected by an electrician to any existing junction box (branch box). This saves time and costs.

Variant

679,00 €

including20% VAT. , plus shipping (Paket)

We produce for you!

Shipping time: 50 days



The go-eCharger HOMEfix 11 kW is a charging box with the highest performance at an unbeatable price-performance ratio. It is suitable for garages and outdoor parking areas, e.g. in front of residential buildings and companies (without selling charging current). The charging station has a 2 meter connection cable for a fixed connection to a power junction box. Thus, unlike the go-eCharger HOME+, the charger has no plug and is therefore not mobile. The clever solution for all who need a smart home charging station for pure wall installation.

In addition to extensive safety functions such as DC fault protection, phase detection and earth measurement, the box is equipped with RFID for access control and hotspot/WLAN. PV connection via the API interface, load balancing and electricity price exchange connection are also part of the functional scope. The charger can be personalized and updated to a large extent via the associated app. Further information and downloads can be found here.

Scope of delivery:

  • Charging station 11 kW with 2 meters connection cable for stationary installation, without plug
  • Wall mount including screws and dowels
  • Optionally mountable cable protection (anti-theft protection)
  • One reset card and one RFID chip
  • One spare special fine fuse
  • Short instructions

Product specifications:

  • Dimensions: approx. 15 x 25 x 9 cm
  • Weight: approx. 2.0 kg
  • Connection cable: 2 m, 5 x 2,5 mm for fixed connection (type H07BQ-F)
  • Rated voltage: 230/400 V depending on number of connected phases
  • Rated frequency: 50 Hz

Permissible ambient conditions:

  • Temperature: -25 C to + 40 C
  • Average temperature in 24 hours: below 35 C
  • Altitude: maximum 2,000 m above sea Level
  • Relative humidity: maximum 95 % (non-condensing)

Charging Capacity:

  • Maximum charging power 11 kW (16 A 3-phase)
  • Charging power adjustable between 1.4 kW and 11 kW (via the charging current in 1 ampere steps between 6 A and 16 A) depending on the number of phases (not adjustable at the go-eCharger!):
    • single-phase: 1.4 kW to 3.7 kW
    • two-phase: 2.8 kW to 7.4 kW (ATTENTION: two-phase connection of the charger is not possible! This information applies to vehicles which have a two-phase onboard charger installed! The go-eCharger has to be connected single-phase or three-phase!)
    • three-phase: 4.2 kW to 11 kW (The go-eCharger switches through the power that is made available to it at the connection.)

Connection on vehicle side:

  • Type 2 socket, own type 2 cable required (not included in delivery)
  • Locking device (theft protection)
  • Vehicles with type 1 can be charged with adapter cable
  • Ampere and charging status readable via LED ring or app
  • Charging power adjustable via button and app

Safety functions:

  • RFID access control
  • RCD protection device with DC detection, 30 mA AC, 6 mA DC
  • Phase and voltage test of the input voltage
  • Phase test after contactor
  • Current sensor three-phase
  • Ground check (switchable grounding monitoring)
  • Customer replaceable fine fuse for internal electronics (triggers if the supply line is connected incorrectly)
  • IP54 - Protection against dirt and water, suitable for permanent outdoor use
  • Impact resistance = IK10
  • Protection class = I
  • Pollution degree = II
  • go-e network operator API for authorised access of the electricity network operator to the go-eCharger for network related power control

App and connectivity:

  • Local (WiFi hotspot) or worldwide (via WiFi) usable
  • Charge monitoring (voltage, current, power, energy)
  • Start/stop function
  • RFID card management (up to 10 users per charger)
  • Timer
  • Electricity meter (total kWh and total amount per RFID card)
  • Max Wh Charging
  • Access management (RFID/App)
  • Cable Lock/Unlock functions
  • Electricity price exchange connection with intelligent charge management
  • Load balancing
  • Photovoltaic connection via open API interface (programming required)
  • LED adjustment
  • Management of the charging levels via button on the charging box
  • Modbus TCP (firmware version 0.40 or higher) for power control by the electricity network operator
  • Updateable for later functions (Smart Home, etc.)

*Please note our information on country-specific obligation to register and/or get approval from the electricity network operator.


Shipping weight: 3.36 Kg
Product weight: 2.02 Kg

Average product review

Share your experience with other customers:

Please login first to add a tag.